Convert Technicolor TG582n Router to a Wireless Access Point in 1 Minute

How To Convert Technicolor TG582n Router to Access Point
Configure Technicolor TG582n router as a Wireless Access point:
convert router to access point
convert router to access point tp-link
convert d’link router to access point
convert tp link router to access point
convert vodafone router to access point
convert router to wireless access point
convert zte router to access point
convert huawei router to access point
convert linksys router to access point
how to convert router to access point
convert old router to access point
convert modem to access point
convert old modem to access point
convert dsl modem to wireless access point
configure mikrotik router as a wireless access point
access point شرح
access point tp link شرح
access point name problem
access point problem
access point router
access point setup
access point names
access point placement
access point vs router
access point audiomachine
access point and router difference
access point antenna
access point adalah
access point airtel
access point as repeater
access point asus
access point aruba
access point barmer
access point beaconhd
access point bangla
access point banyak user
access point bridge
access point bridge mode
access point bridge mode configuration
access point bearer
g-240w-b access point
access point configuration
access point cisco
access point configuration cisco packet tracer
access point ceiling mount
access point controller
access point configuration step by step
access point device
access point dlink
access points diamond casino heist
access point d-link شرح
access point dlink (dap-1360) wireless n300
access point dual band
access point dhcp
access point deco
d’link access point setup
d link router access point configuration
d’link outdoor access point
d’link 1360 access point configuration
dlink 2730u as access point
d’link access point dap 1360
access point d-link
access point explained
access point extender
access point eap110
access point ethernet
access point einrichten
access point epic music
access point esp8266
access point established
how to access e points in pes
diferença repetidor e access point
diferença roteador e access point
diferença entre access point e repetidor
differenza tra access point e repeater
access point for airtel
access point for jio
access point for vi
access point for home
access point for airtel 4g
access point flexhd
access point full wifi
access point for smart lte
access point globe
access point gaming
access point gta casino heist
access point gigabit
access point grandstream
access point gigabit wireless
access point green light
access point gartner 2020
linksys wireless-g access point اعدادات
wireless-g access point
access point huawei
access point high power
access point how it works
access point huawei hg8245h
access point huawei hg8245a
access point horizontal or vertical
access point how to set up
access point installation
access point in networking
access point in iphone
access point in-wall hd
access point in cisco packet tracer
————————————————————————–
*With DHCP enabled on the network:

In order for this to work, you must not be connected to the router at the time. Unplug your computer and restart the router to make sure.

1) Plug the router into the network via port #4 (marked red)
2) Wait until the router appears to have an IP address
3) Connect your computer to the router wired or wirelessly.

*With DHCP disabled on the network:

It’s best to factory reset the router before doing this.
1) Power on the router and wait a few minutes.
2) Plug your computer into the router via ports 1, 2, or 3
3) Using Internet Explorer browse to 192.168.1.254. By default, the router does not have a password so you should be able to log straight in.
4) Go to Home Network, Interfaces, Click on ‘LocalNetwork’, and then Configure (top right)
5) Add a new IP address for the router (e.g. 192.168.100.101 if the network’s current gateway is 192.168.100.253). The second box is the Subnet Mask and usually 255.255.255.0.
6) Click configure, untick DHCP, and apply.
7) Click on Configure and Edit/Add a new DHCP range that fits in with the existing network (e.g. 192.168.100.101 – .200 if the networks current gateway is 192.168.100.253)
8) Go to configure, tick DHCP again, and then apply.
9) Delete the previous setting (was 192.168.1.254). This will disconnect you.
10) Restart the router or unplug your Ethernet cable for 10 seconds then plug it back in. The router should assign you an IP address within the new range and you should be able to connect to the router on its new IP address. .