Cisco Vlan and Trunk Port
No:1 vlan id
switch#en
switch#conf t
Switch(config)# vlan 101
Switch(config)# vlan 102
Switch(config)# vlan 103
Switch(config)# vlan 104
Switch(config)# vlan 105
Switch(config)# vlan 106
Switch(config)# vlan 107
Switch(config)# vlan 108
exit
exit
show vlan
=================
No: 2 taging the vlan to the port 1 to 8
Switch#en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface fastEthernet 0/1
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 101
Switch(config-if)#interface fastEthernet 0/2
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 102
Switch(config-if)#interface fastEthernet 0/3
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 103
Switch(config-if)#interface fastEthernet 0/4
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 104
Switch(config-if)#interface fastEthernet 0/5
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 105
Switch(config-if)#interface fastEthernet 0/6
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 106
Switch(config-if)#interface fastEthernet 0/7
Switch(config-if)#switchport mode access
Recursive Routes in RoS 7.x hadi network
Recursive Routes – MikroTik
Recursive routing for failover
Dual WAN failover using recursive routing
RouterOS 7.5 – failover with recursive routing and PBR
Dual WAN Recursive Failover ROSv7
Related searches
mikrotik dual wan failover recursive
how to setup mikrotik router as failover on two connections
recursive routing example
mikrotik failover configuration
mikrotik dual wan router
mikrotik failover recursive
recursive routing gre tunnel
how to configure auto failover in mikrotik router
Recursive routing on Mikrotik
ROS 6.49.6 How to fix or improve config for Recursive Routing
3 recursive route failover
MikroTik MTCRE – Recursive Routing (Easy Automatic Failover)
MikroTik RouterOS v7 dual DHCP WAN recursive failover w
Recursive routing on Mikrotik
mikrotik dual wan failover recursive
how to setup mikrotik router as failover on two connections
recursive routing example
mikrotik failover configuration
mikrotik dual wan router
mikrotik failover recursive
recursive routing gre tunnel
how to configure auto failover in mikrotik router
Basic ISP Failover with MikroTik
Switch(config-if)#switchport access vlan 107
Switch(config-if)#interface fastEthernet 0/8
Switch(config-if)#switchport mode access
Switch(config-if)#switchport access vlan 108
Switch(config-if)#exit
Switch(config)#exit
=============
No: 3 Trunk Port
Switch#conf
Switch#configure ter
Switch#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#inter
Switch(config)#interface gi
Switch(config)#interface gigabitEthernet 0/1
Switch(config-if)#switchport mode trunk
Command rejected: An interface whose trunk encapsulation is “Auto” can not be configured to “trunk” mode.
Switch(config-if)#switchport trunk enca
Switch(config-if)#switchport trunk encapsulation dot
Switch(config-if)#switchport trunk encapsulation dot1q
Switch(config-if)#switchport mode trunk
Switch(config-if)#switchport trunk allow vlan 101-107
exit
exit
wr
no shut down
reload
========================== .
Comments are closed.